Click Here

Every person is bound to have their private assumption with regards to Tools You Need to Install a New Bathtub .

Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily accessible, the job can move rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub and also embeded in the new one. Make certain you have actually certified yourself for the job and also are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This article will certainly aid you mount a brand-new tub in your restroom if you have already purchased a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your tools as well as product list need to make up the following:

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Installment

To start with, the sustaining framework supplied with the bath should be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets unit to prevent strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its last setting.

Removing Old Taps

If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite troublesome due to the limited gain access to that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

Mounting the Bath tub

Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bath tub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest versatile faucet connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait up until the bath tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making sure that the washing machines remain in location in between the tap as well as the sink. Protect the tap in position with the maker offered backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

Tiling Around the Bathtub

In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, creating the water to permeate the wall between the bathroom and also the tiling, resulting in issues with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the activity experienced when the tub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or waterproof sticky and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I was made aware of that editorial on Tools You Need to Install a New Bathtub from someone on our other site. Do you know about anybody else who is very much interested in the niche? Take a moment to share it. I treasure reading our article about Tools You Need to Install a New Bathtub .

Urgent plumbing? Call us.